Store Reviews ( 3 ) RSS Feed
0 1 2 3 4 (5,0/5)

Review By Rickey Long, 0 1 2 3 4
Rickey Long
As a hobbyist gunsmith, I wanted to try my hand at barrel threading. I had a Moisin Nagant that I w ...
May 7, 2019
Verified Purchase
Review By TLC, 0 1 2 3 4
Deltac laser cut extended slide lock is the best part to replace the factory Glock slide lock in Gen ...
Feb 24, 2018
Review By Richard, 0 1 2 3 4
Ordered items were exactly as expected - very fast processing and shipping.
Apr 9, 2017

Viewed products

Online only

DELTAC® "Slingshot" muzzle brake for Mosin Nagant - Complete threading kit


New product

This item cannot ship outside the United States due to export restrictions

More details

By buying this product you can collect up to 9 loyalty points. Your cart will total 9 loyalty points that can be converted into a voucher of $1.80.


Add to wishlist

More info

We believe that threading the barrel of the Mosin Nagant is the most effective method to install a muzzle brake on your Mosin Nagant because their barrel are not always concentric. See the picture above. There are many breaks on the market that just mount with a bracket secured behind the front sight that end up being shot off with an exiting bullet and are potentially dangerous. Threading your barrel with the use of the enclosed threading tool insure your thread are true and are permanent but ensure reliability and accuracy. We also suggest this to be done by a gunsmith.
Type: Muzzle Brake 
Length: 2.520 inches
Caliber: 7.62
Exit hole .340 inches
Thread:  M15x1 RH (Right hand threads)
Machined from top quality steel and finished in black oxide. 
Threading Die
Round adjustable die in M15X1RH (Right hand threads)
Thread alignment tool:
This is a simple TAT (thread alignment tool) for re-threading 7.62 caliber muzzles to accept the above M15 X 1 RH muzzle device. 
The extended 3" long stem helps with *Mosin-Nagant barrels which have been counter-bored to renew the muzzle crown.. 
It helps you get the die started level and on-center to prevent costly mistakes. 
Material: 303 Stainless Steel
#5 Die Handle
This a heavy duty #5 die handle is approx. 11.5in long and accepts 1.5in dia (38mm) dies like the M15X1 RH die that we offer on this site.  The handle ends are not removable. These are high quality handles made of high tensile steel.
* The Russian arsenal sometimes counter-bore the barrels to prolong their life by cutting out the bad/worn rifling at the muzzle end. If done properly a counter-bore has the potential to improve accuracy.  The length of the counter-bore depended on how worn the muzzle end was. You should measure the depth of the counter-bore to make sure that this tool is long enough to reach the caliber bore of the rifle.
PKG Content:
  • 1 Threaded muzzle break
  • 1 M15X1 RH Die
  • 1 Thread alignment tool with a 3" long stem
  • #5 die handle
  • 1 Jam nut

Muzzle Threading Instructions
Screw the TAT about 4-5 threads into the back of the die with the pilot
sticking out in front.
Insert die and TAT into handle, preferably lettered towards you and aligning
at least one of the tightening screws in the handle with the divots in the die
Secure the barrel vertically in a padded vise
Apply a good cutting fluid/oil to the die teeth and start cutting. It will take a
little bit of vertical downward pressure to get started. Apply even downward
pressure and rotate the die slowly.
Repeatedly advance the die about 1/8 turn, then back it off to break up the
shaving (chips).
Do not allow the face of the TAT to ever reach the barrel face. This could
strip the teeth out, possibly damaging the TAT and ruining the few threads
that you have cut on the
Once you’ve cut about 4-5 threads, and before the TAT reaches the barrel
face, unscrew the die completely, loosen the 2 tightening screws on the die
holder, and remove the TAT.
With the TAT removed, put the die back in the handle and hand tighten the 2
tightening screws.
Resume threading as above, breaking the chips and applying cutting fluid as
you go.
Thread to the desired depth, blow off the threads and check the fit with
whatever muzzle device you plan to use. You want the threads firm but able
to screw on by hand.
If your threads are too large, tighten the 2 screws in the handle a little bit,
apply more cutting fluid and run over the threads again. Blow off the threads
and check the fit again. Repeat as needed.
If necessary, you can take the die out of the handle, unscrew the preset screw
in the die itself, and place back in handle, tightening the 2 screws for an even
smaller thread.
Hopefully this information will help you successfully complete your barrel
threading project. Make sure to wear protective glasses throughout the
process and Take Your Time!. This type of work can be very rewarding
when all goes smooth, or a disastrous, aggravating, mess if you try to rush.
NOTE: This device should be installed by a competent gunsmith to ensure concentricity and clearance at exit hole.

Reviews Reviews (3)

Total rating:
0 1 2 3 4
Based on 3 reviews
0 1 2 3 0 (0)
0 1 2 0 1 (0)
0 1 0 1 2 (0)
0 0 1 2 3 (0)
0 1 2 3 4

Muzzle Barrel Threading for Moisin Nagant

2 of 2 people found the following review helpful
Total Rating:0 1 2 3 4

First time purchase and attempt as a hobbyist gunsmith. This tool was all I expected. Easy to read/follow instructions. I would definitely recommend.

0 1 2 3 4

Mosin barrel threading...

1 of 1 people found the following review helpful
Total Rating:0 1 2 3 4

The kit was complete, well made and very easy to use. The finished product is clean and the brake is very effective. I have cut the barrel back to 23.5 inches and re-crowned it, I had to open-up the threading die a good bit to fit the shortened barrel and cut it a couple of times but it is clean and works perfectly. Clocked the brake so the jam nut was not needed. I recommend this product to anyone wishing to improve upon their Mosin at a very fair price. It takes little skill to do a great job.

0 1 2 3 4

Mosin Nagant,

0 of 0 people found the following review helpful

Mosin Nagant I received my kit quickly and instructions were very clear

The customer has rated the product but has not posted a review, or the review is pending moderation

Page: 1

Related articles on blog