2. AK/SKS/PSL Accessories
  3. DELTAC® Slingshot Muzzle Brake for AK-47 - Complete threading kit

Last blog articles

Kel-Tec Sub 2000 9mm — The Home Defender Kel-Tec Sub 2000 9mm — The Home Defender

DELTAC Extended slide lock for Glock Gen 1-4 VS Gen 5 DELTAC Extended slide lock for Glock Gen 1-4 VS Gen 5

Don't Lie Campaign

The Proper Pistol Grip The Proper Pistol Grip

Don’t Lose Your Thumb! How to Correctly Grip Your Revolver Don’t Lose Your Thumb! How to Correctly Grip Your Revolver

See all

Search on blog

eBay feedback

99,4% of positive feedback
Item as described:
Communication:
Shipping time:
Shipping charges:

Last Product Reviews
RSS Feed

DELTAC® Extended Slide Lock For GLOCK 44
DELTAC® Extended Slide Lock For GLOCK 44
The customer has rated the product but has not posted a review, or the review is pending moderation
By Terry Terry on Dec 7, 2024
DELTAC Extended Slide Lock release Lever For Smith & Wesson S&W Sigma SW9VE
DELTAC Extended Slide Lock release Lever For Smith & Wesson S&W Sigma SW9VE
(5/5)
0 1 2 3 4
Great product. Works as described. Great shipping, good price.
By Thomas S Thomas S on Oct 17, 2024
Verified Purchase
DELTAC® Extended Slide Lock For GLOCK 44
DELTAC® Extended Slide Lock For GLOCK 44
(5/5)
0 1 2 3 4
This is one of the most simple and important parts to upgrade. Makes the ta...
By Rick Cox Rick Cox on Aug 28, 2024
View All Reviews

Store Reviews ( 0 ) RSS Feed
0 1 2 3 4 (0/5)

There are not store reviews yet.
See all Store Reviews
Previous Next

Online only

DELTAC® Slingshot Muzzle Brake for AK-47 - Complete threading kit

PKG128-7.62

New product

Total Rating Total Rating:

0
0/5 - 0 reviews

View ratings
0 1 2 3 40
0 1 2 3 00
0 1 2 0 10
0 1 0 1 20
0 0 1 2 30

 Add Review View Reviews View Reviews

$94.99

More info

We believe that threading the barrel of the AK47 is the most effective method to install a muzzle brake. Threading your barrel with the use of the enclosed threading tool insure your thread are true and are permanent but ensure reliability and accuracy. We also suggest this to be done by a gunsmith.

Type: Muzzle Brake 
Length: 2.520 inches
CALIBER: 7.62
Exit hole .340 inches
Thread:  M14x1 LH (Left thread).
M14x1.0 LH Die
New adjustable die in M14x1LH (Left hand thread)
Recommended barrel OD sizes for threading is 0.5431 min and 0.5501 max
 
Thread alignment tool:
This is a simple TAT (thread alignment tool) for re-threading 7.62 caliber muzzles to accept the above M14 X 1 LH muzzle device. 
Made of Stainless Steel 303. It helps you get the die started level and on-center to prevent costly mistakes. 
 
#5 Die Handle
This a heavy duty #5 die handle is approx. 11.5in long and accepts 1.5in dia (38mm) dies like the M14X1 LH die that we offer on this site.  The handle ends are removable. These are high quality handles made of high tensile steel.
Note: 
Recommended barrel OD sizes for threading using this kit is is 0.5431 min and 0.5501 max

PKG Content:

  • 1 Threaded muzzle break
  • 1 adjustable M14X1 LH Die
  • 1 Thread alignment tool 
  • #5 die handle
  • 1 Jam nut

Muzzle Threading Instructions
 
Screw the TAT about 4-5 threads into the back of the die with the pilot
sticking out in front.
Insert die and TAT into handle, preferably lettered towards you and aligning
at least one of the tightening screws in the handle with the divots in the die
OD.
Secure the barrel vertically in a padded vise
 
Apply a good cutting fluid/oil to the die teeth and start cutting. It will take a
little bit of vertical downward pressure to get started. Apply even downward
pressure and rotate the die slowly.
Repeatedly advance the die about 1/8 turn, then back it off to break up the
shaving (chips).
 
Do not allow the face of the TAT to ever reach the barrel face. This could
strip the teeth out, possibly damaging the TAT and ruining the few threads
that you have cut on the
barrel.
Once you’ve cut about 4-5 threads, and before the TAT reaches the barrel
face, unscrew the die completely, loosen the 2 tightening screws on the die
holder, and remove the TAT.
 
With the TAT removed, put the die back in the handle and hand tighten the 2
tightening screws.
Resume threading as above, breaking the chips and applying cutting fluid as
you go.
 
Thread to the desired depth, blow off the threads and check the fit with
whatever muzzle device you plan to use. You want the threads firm but able
to screw on by hand.
 
If your threads are too large, tighten the 2 screws in the handle a little bit,
apply more cutting fluid and run over the threads again. Blow off the threads
and check the fit again. Repeat as needed.
 
If necessary, you can take the die out of the handle, unscrew the preset screw
in the die itself, and place back in handle, tightening the 2 screws for an even
smaller thread.
 
Hopefully this information will help you successfully complete your barrel
threading project. Make sure to wear protective glasses throughout the
process and Take Your Time!. This type of work can be very rewarding
when all goes smooth, or a disastrous, aggravating, mess if you try to rush.
NOTE: This device should be installed by a competent gunsmith to ensure concentricity and clearance at exit hole.

Reviews Reviews (0)

Total rating:
0 1 2 3 4
0/5
 Based on 0 reviews
Filter:
0 1 2 3 4 (0)
0 1 2 3 0 (0)
0 1 2 0 1 (0)
0 1 0 1 2 (0)
0 0 1 2 3 (0)
Write a Review

Related articles on blog

Customers who bought this product also bought: