Online only

DELTAC MOSIN NAGANT SCOUT SCOPE MOUNT M9130, M38, M44 and T53

3MNT112

New product

By buying this product you can collect up to 5 loyalty points. Your cart will total 5 loyalty points that can be converted into a voucher of $1.00.


$59.99

Add to wishlist

More info

  • Each mount is Milled from a solid piece of 6061 Aluminum for strength and rigidity
  • No drilling and No Permanent modification required
  • Fits Mosin Nagant M9130, M38, M44 and T53
  • Requires a long eye relief scope
  • Convert Your Mosin Nagant into a Modern Hunting Rifle!

Product Description

  • Mosin Nagant Scout Scope Mount
  • Extended Top Rail with 6 Slots to Provide Adequate Eye Relief Adjustment Space
  • Great Zero Retention Capability for All Accessories Installed on the Rails
  • Assembly Hardware and Detailed Instructions Included
  • Limited Lifetime Warranty


Note: Due to the large production quantities and variations of this rifle as well as the manufacturing principles used during the production period some modification may be needed. If you do not possess the equipment or skill set necessary for installation, we recommend that an accredited gunsmith completes the installation process.

Fits: Mosin Nagant M9130, M38, M44, T53

Pkg Includes
  • 1 Deltac scout Scope mount
  • 2 socket head screw
  • 2 M3 nut
  • 2 lock washer
  • 4 steel washer
  • 1 Pin removal punch
  • 1 hex key

Reviews Reviews (12)

Total rating:
0 1 2 3 4
4,50/5
Based on 12 reviews
Filter:
0 1 0 1 2 (0)
0 0 1 2 3 (0)
0 1 2 3 4
(5/5

Good scope mount

0 of 0 people found the following review helpful
Total Rating: 0 1 2 3 4

Perfect. It fits perfect and snug.

0 1 2 3 4
(4/5

So far so good. Don't use provided tools.

0 of 0 people found the following review helpful
Total Rating: 0 1 2 3 4

So far so good. Haven't shot weapon yet to verify mount's reliability, but feels solid once attached. Word to the wise, Do NOT use the punch provided with the mount. It is way too weak and flimsy to move anything but already-loosened pins from the existing sight base. Luckily, I had real punches that would move the pins as needed.

0 1 2 3 4
(4/5

Four Stars

0 of 0 people found the following review helpful
Total Rating: 0 1 2 3 4

Fit perfectly

0 1 2 3 4
(3/5

But if you tighten the one that you can get through as tight as you can it will stabilize but you need to use something like loc

0 of 0 people found the following review helpful
Total Rating: 0 1 2 3 4

I Dont think this is for a russian mosin because in the instructions it says there should be 2 pins that line up with the holes but there is only the one in the front of the sight base that you can use for the mount. you will have to drill a hole to make it so that both of the bolts and nuts go through if you want both of the bolt/screws to be used. But if you tighten the one that you can get through as tight as you can it will stabilize but you need to use something like lock tight on the screw/bolt and nut otherwise it will just loosen up after 5 shots other than that it is a decent product.

0 1 2 3 4
(4/5

It works.

0 of 0 people found the following review helpful
Total Rating: 0 1 2 3 4

Follow mounting directions. Dry fit it before using Loctite on the threads. You need to "true" it with the rifle barrel to make it easier to zero in your scope. On my my 1943 R Carbine, I had to use a 3mm drill bit on the rifle's rear sight mount screw hole. The front screw went in with no problem, but the rear was just slightly off due to the bore hump. All Mosins are different, so your experience may differ from mine. I made a wooden shim/jig to place on the barrel and under the mount to hold it in place while tightening the screws.

Page: 1 2 3

Related articles on blog